Your disposal hums but won't spin โ the impeller plate is jammed. It's completely silent when you flip the switch โ the thermal overload protector has tripped or the motor has failed. Water drips from the sink collar โ the sink mounting gasket has deteriorated. Each of these is a different diagnosis, and each has a different solution. Masters Plumbing Service's techs in Richvale, CA arrive with the jamming tools, reset wrench, and replacement units to resolve any disposal failure same visit.
๐ Call +1-855-718-1500 โ Same-Day Service
Garbage disposal failures have specific, diagnosable causes. Our techs don't just swap units โ they identify what failed and whether repair or replacement is the right call for your situation.
A disposal that hums but won't spin almost always just needs the jam cleared with an Allen wrench at the center socket and the reset button pressed โ a 5-minute fix that doesn't require a new unit.
InSinkErator (Badger, Badger 5, Compact, Evolution series), Moen GXS/GX series, Waste King, KitchenAid, and Whirlpool disposals all mount differently and have specific jam-clearing procedures. We know the mounting assembly for each brand and carry the correct jam-clearing wrench sizes.
We give you the actual cost comparison. If clearing the jam and pressing the reset button fixes it, that's what we do. If the motor has failed, we show you the replacement options and install same-day.
A disposal isn't an isolated appliance โ it connects to the sink drain, the dishwasher drain (if present), and the drain arm leading to the p-trap. We inspect the full connection set during any disposal call: drain arm slope, dishwasher drain knockout (if a dishwasher is being added), and p-trap connection integrity.
Most disposal calls complete in 30โ60 minutes โ same visit, flat-rate pricing.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
We identify the leak source before recommending any repair. A sink collar re-seal is a 30-minute job. A unit with a cracked body has no cost-effective repair and warrants replacement.
An unusually loud grinding, rattling, or metal-on-metal sound from a disposal almost always means either a hard object (bottle cap, small utensil, pit from stone fruit) is in the grinding chamber, or an impeller piece has broken and is contacting the shredder ring. We access the grinding chamber safely, remove any foreign objects, and inspect the impeller and shredder ring for damage.
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
Replacement includes: safely disconnecting electrical at the junction box under the sink, removing the old unit and mounting assembly, installing the new unit with correct wiring and plumbing connections, testing for full jam-free operation, and verifying zero leaks at all connections before leaving.
No guesswork โ we diagnose before we quote, and quote before we start.
Hums but won't spin, completely silent, grinding noise, leaking, or slow to drain โ each symptom tells our dispatcher which tools and possible replacement units to have on the truck. Knowing the disposal brand is a plus but not required.
For leaks, we dry the area completely and run a short test cycle to confirm exactly which connection is dripping.
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
We leave the cabinet dry and the disposal running quietly. If a dishwasher drain hose was involved, we run a dishwasher cycle to verify no backup occurs.

Disposal hummed and wouldn't spin. I'd already tried the Allen wrench trick without success. Masters Plumbing Service's tech came out, worked the impeller free from underneath while removing a piece of broken ceramic that had fallen in โ it had wedged between the impeller and the grinding ring in a way I couldn't have cleared from the top. Cleared the jam, pressed the reset, tested. Five-minute fix. Honest about the call minimum charge, no attempt to upsell a replacement on a perfectly good motor.
After we added a dishwasher, it started backing up every cycle. Masters Plumbing Service found the problem immediately โ the previous installer had forgotten to knock out the dishwasher drain plug inside the disposal inlet. The plug was blocking the drain port. Two-minute fix. The tech also tightened the dishwasher drain hose clamp, which was loose. Never had another backup.
Old disposal stopped working completely โ no hum, nothing. I assumed the motor failed. The tech checked the wiring first โ found a loose wire nut at the junction box under the sink that had vibrated loose over the years. Reconnected the wire, reset the overload button, disposal came right on. Would have been embarrassing if I'd bought a replacement unit. Masters Plumbing Service's thoroughness saved me a few hundred dollars.

Masters Plumbing Service dispatches garbage disposal repair and replacement technicians throughout Richvale and the broader Richvale, CA service area. Most calls are same-day โ call to check today's availability.

Call now โ same-day service available in Richvale and across Richvale, CA.
๐ Call +1-855-718-1500 Now